Parts
by Spencer Bradley

7 Air Ride Suspension Kits for Harley Davidson

November 20, 2020
0
Share

Since our launch of ThrottleGR, I have been asked on multiple occasions to develop a post on some top Air Ride Suspension Kits for Harley Davidson. We have also developed an article around the best non Air Ride Harley Davidson Shocks for your ride as well.

For those of you motorcycle riders that are seeking a much smoother ride and looking to turn your bikes into a show vehicle that will be guaranteed to turn heads, an air ride suspension is a great option.  In this article, we will be covering suspension options for larger touring motorcycles such as a Harley Davidson Street Glide, Road Glide, Road King, or Electra Glide.  These are typically the bikes you see air ride suspension kits included in because of these motorcycle’s weights and they are simply put, the most common rides that have a lot of aftermarket furnishings added to them.

The primary benefit of adding an air ride suspension is ride quality: Vehicles with air suspension are often said to “glide” over bumps, while traditional steel spring suspension can cause a harsher ride. Also, air suspension is often adjustable. Daily driving around in the city should be fine in most cases, but excessive speeds on the highway could lead to damage of air ride components and is not recommended.

Keeping all of this in mind, we would like to present you with our top choices of air ride suspension kits for Harley Davidson.

XFMT Adjustable Rear Air Ride Suspension Kit

Aftermarket 100% brand new. This is a complete kit assembled to replace your stock touring shocks with height-adjustable air shocks. Fully Collapsed at approximately 9.64inches(24.5cm); fully extended 14.17inches(36cm). This kit will allow you to lower your bike 2 to 3 inches with all of the air released. Then air it up to stock ride height for a smooth ride in a matter of seconds.

The system uses all nickel-plated brass high-flow high-pressure push-to-connect fittings throughout the entire system and a manifold-style dump valve block for optimum performance.  This kit includes all of the components for a fully functional, fully height-adjustable rear air suspension. With this kit, you can ride with zero air pressure without rubbing. That means you can cruise around with your bike SLAMMED, or also if you ever lost air pressure for any reason you can still ride without rubbing your tire against your fender (on most ’09-Later models, or ’08-earlier models with the stock rear tire).

XFMT Electric Center Stand Kits + Rear Air Ride Suspension

This kit comes with a center stand and is aftermarket, 100% brand new. This item is black and made of metal, aluminum, and stainless steel. This item can be bolted on in minutes and use a linear actuator to raise and lower the legs electronically. Two Aluminum legs provide a very sturdy base and allow the motorcycle to sit upright while parked.

This kit also comes with a rear air ride suspension. This is a complete kit assembled to replace your stock touring shocks with height-adjustable air shocks. Fully Collapsed at approximately 9.64inches(24.5cm); fully extended 14.17inches(36cm). This kit will allow you to lower your bike 2 to 3 inches with all of the air released. The air it up to stock ride height for a smooth ride in a matter of seconds. The system uses all nickel-plated brass high-flow high-pressure push-to-connect fittings throughout the entire system and a manifold-style dump valve block for optimum performance. This kit includes all of the components for a fully functional, fully height-adjustable rear air suspension.

XFMT Rear Air Ride Suspension with Air Tank

Waterproof and dust-proof (IP)：IP54. Output Voltage：DC-12V. Working Period：15%@100PSI. Maximum Working Voltage：130PSI(9.1KG/c㎡). Maximum current：14A. Pump’s Size(L×W×H)：152mm × 88.5mm × 135mm. The Ventilating Flux: 1.27CFM@0PSI, When under 0PSI, the rate of flow is approximately 36.0L/minute. 

The system uses all nickel-plated brass high-flow high-pressure push-to-connect fittings throughout the entire system and a manifold-style dump valve block for optimum performance.  This kit includes all of the components for a fully functional, fully height-adjustable rear air suspension.   With this kit, you can ride with zero air pressure without rubbing. That means you can cruise around with your bike SLAMMED, or also if you ever lost air pressure for any reason you can still ride without rubbing your tire against your fender (on most ’09-Later models, or ’08-earlier models with the stock rear tire, contact us for details).

SLMOTO Air Ride Suspension Kit Fit For Harley Touring

Fitment:
Fits all Harley touring models 1994-2018

Features:
This is a complete kit assembled to replace your stock touring shocks with height-adjustable air shocks.)
Fully Collapsed approx. 9.64inches(24.5cm); fully extended 14.17inches(36cm).)

Upgraded Gas nozzle

360 degree rotation, and connecting directly which can defent leaking air.
This kit will allow you to lower your bike 2 to 3 inches with all of the air released.)
The air it up to stock ride height for a smooth ride in a matter of seconds.)

System uses all nickel-plated brass high-flow high-pressure push-to-connect fittings throughout the entire system, and a manifold-style dump valve block for optimum performance. This kit includes all of the components for a fully functional, fully height adjusta ble rear air suspension. With this kit, you can ride with zero air pressure without rubbing. That means you can cruise around with your bike SLAMMED, or also if you ever lost air pressure for any reason you can still ride without rubbing your tire against your fender (on most ’09-Later models, or ’08-earlier models with stock rear tire, contact us for details).)

(Note：Installation instructions Included)
All of our products are brand new items. Because of a new process for treating, a little bit of paint loss from packaging and long distance delivery as shown on picture. This is normal and will never affect the functionality and safety of the item.)

Legends Aero-A Adjustable Air Suspension

All the benefits of the new AERO suspension systems. Plus six external knob adjustments allow the fine-tuning of rebound damping provide optimum rebound performance for any given rider weight, personal ride quality preference or personal riding style. Light to heavy riders can fine-tune ride preference. Riders with aggressive to casual styles can tune to desired quality or personal preference. Made in the U.S.A.

Arnott MC-2904 Fox Series FLH/FLT Air Suspension

Arnott Ultimate Ride Adjustable Air Suspension System (with adjustable rebound). Custom designed for Harley Davidson models to give the rider superior control, additional ride comfort settings and fast ride height adjustability. The FOX shock’s custom valving, designed for your motorcycle, provides you with a safe and comfortable ride.

Arnott’s patent-pending kit offers TruAIR technology with a rugged air spring bladder and shock damper design, not an air cylinder or air-assisted unit. For added ride comfort, this kit includes FOX’s adjustable rebound control dial so you can quickly adjust your shocks’ internal damping characteristics – a feature not found elsewhere in the air suspension market.

Each kit includes everything you need for a fast and flawless installation, including a detailed installation manual, a fused wiring harness, and relay assembly, handlebar-mounted inflation switch, all necessary tubing, wiring, cable ties, fittings, bolt covers, and mounting accessories.

Legends Aero HVG Air Suspension

All new AERO suspension systems set the high mark in ultimate ride quality. New, redesigned exclusive Kevlar air spring technology provides spring rate adjustability. Air springs maximize wheel travel and adjust to any desired ride height. Fitment accommodates 13in. and 12in. needs. Spherical mount bearings top and bottom. Hard anodized machined aluminum bodies. Legends low-friction seals eliminate stiction. High Flow Piston reacts quickly for improved fluid flow management. Deflective Disc Valved Damping self-adjusts to the frequency and ensures controlled performance. Include a high-volume hand pump with an inline gauge. Optional fairing-mounted matching gauges available separately. Made in the U.S.A.

Related Posts
Harley Davidson Touring Headers

Best Harley Davidson Touring Headers

January 27, 2023
0

 

Harley Davidson is a brand synonymous with touring motorcycles. With a wide range of models to choose from, it can be difficult to decide which one is the best for you. In this article, we will take a look at the top Harley Davidson touring motorcycle headers currently on the market.

Vance & Hines Power Duals Headers

Vance & Hines Power Duals Headers: These headers are a popular choice among Harley Davidson touring motorcycle enthusiasts. They feature a sleek design that complements the lines of the motorcycle, and they provide a noticeable increase in horsepower and torque. The Vance & Hines Power Duals Headers are made from high-quality stainless steel and come with a limited lifetime warranty.

Rinehart Racing Slimline Duals Header Kit

Rinehart Racing True Dual Headers: Another popular option among Harley Davidson touring motorcycle riders, these headers feature a unique design that allows for maximum performance. The Rinehart Racing True Dual Headers are made from high-quality stainless steel and come with a limited lifetime warranty. They have a deep and rich exhaust note, which adds to the overall riding experience.

 

Bassani Road Rage III 2-into-1 Headers

Bassani Road Rage III 2-into-1 Headers: If you’re looking for a more aggressive look and sound, the Bassani Road Rage III 2-into-1 headers might be the perfect fit for you. These headers are made from high-quality stainless steel and come with a limited lifetime warranty. They provide a noticeable increase in horsepower and torque, and the unique design gives the motorcycle a more aggressive look and sound.

Cobra Speedster Swept HeadersCobra Speedster Swept Headers: These headers are designed to give the Harley Davidson touring motorcycle a more streamlined look and a deeper, more aggressive sound. The Cobra Speedster Swept Headers are made from high-quality stainless steel and come with a limited lifetime warranty. They provide a noticeable increase in horsepower and torque and are designed to fit seamlessly with the lines of the motorcycle.

In conclusion, Harley Davidson touring motorcycles are a popular choice among riders for their power and comfort. The headers are an important component of the motorcycle’s exhaust system and can greatly enhance the performance and sound. The Vance & Hines Power Duals Headers, Rinehart Racing True Dual Headers, Bassani Road Rage III 2-into-1 Headers, and Cobra Speedster Swept Headers are all excellent choices for those looking to upgrade their Harley Davidson touring motorcycle. It’s important to note that before making any modifications, be sure to check your local laws and regulations regarding aftermarket exhaust systems.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13 Best Ape Hanger Handlebars for Harley Davidson Baggers

September 19, 2019
0

Handlebars for motorcycles come in a variety of different shapes and sizes to align with your riding style and comfort fit.  In my opinion, if you want to take your motorcycle from a lean look to a mean look, adding a pair of the best Ape Hanger handlebars for Harley Davidson can get you there.  Not only do I prefer the feel of my 14” Ape Hangers but the added flair it gives my bike is priceless.  Like I mentioned previously, the best part of handlebars for motorcycles is that they come in all different shapes and sizes to fit your exact arm length and height as a rider.

Handlebars are made from round-section metal tubing, typically aluminium alloys or chrome plated steel but also of carbon fiber and titanium, shaped to the desired contour. Holes may be drilled for the internal routing of control cables such as brake, throttle, and clutch. Risers hold the handlebars above their mounting position on the upper triple clamp or the top of the fork, and may be integrated into the bar itself or separate items. Each handlebar end may contain bar-end weights to damp vibration by isolating the bar’s resonant frequency from that of the engine. Electrically heated grips may be fitted to provide warmth for the rider in cold weather.

If you’ve been considering making the switch from your stock handlebars to some badass Ape Hangers, you’re in luck. We’ve compiled the top 13 Ape Hanger Handlebars for Harley Davidson Baggers that will transform your ride.

Included in this list of handlebars are options that will fit several different Harley Davidson models including Electra Glides, Street Glides, Road Glides, Ultra Glides, and more! Whether you are going for that vintage look or simply a custom feel, the Ape Hangers we have chosen are a great start in your decision making process. Don’t forget to check out the Best Grips for Harley Davidson Motorcycles to go with your new ape hanger handlebars.

Dominator Industries 1 1/4″ Gloss Black 12″ Meathook Monkey Bar Ape Hanger Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4″ Chrome 14″ Meathook Monkey Bar Ape Hanger Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4 Inch Meathook Monkey Bagger Ape Hanger Handlebars, 10 Inch Rise, Chrome

When we introduced our Meathook Bagger Ape Handlebars for the 1996-2018 model years of the Harley-Davidson Electra Glide (FLH), Electra Glide Classic (FLHTC), and Street Glide (FLHX) our goal was to combine classic styling and unique attitude for Harley-Davidson owners that want the best quality with no compromises.  Ride comfort and easy installation make choosing Dominator Industries handlebars to customize your bike a no-brainer.

All of our parts are hand-made in the USA employing a multi-step manufacturing process using the finest materials. Tube diameter is 1.25” stepped down to 1” for stock/conventional controls.  Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire but also fits cable throttle systems. Laser cut tubing yields the smoothest corners with no slag for easy wiring. The Knurled Center for non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment.

There have been many copycat attempts to replicate our products but many customers over the years have come back because of our superior quality.  We also pride ourselves in our smooth and clean arched corners whereas competitors often use straight sharp edges which are easier to manufacture but fall short of the premium styling distinguishing riders demand.

Dominator Industries 1 1/4″ Chrome 12″ Meathook Monkey Bar Ape Hanger Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4″ Gloss Black 10″ Meathook Monkey Bar Ape Hanger Handlebars

When we introduced our Meathook Bagger Ape Handlebars for the 1996-2018 model years of the Harley-Davidson Electra Glide (FLH), Electra Glide Classic (FLHTC), and Street Glide (FLHX) our goal was to combine classic styling and unique attitude for Harley-Davidson owners that want the best quality with no compromises.  Ride comfort and easy installation make choosing Dominator Industries handlebars to customize your bike a no-brainer.

All of our parts are hand-made in the USA employing a multi-step manufacturing process using the finest materials. Tube diameter is 1.25” stepped down to 1” for stock/conventional controls.  Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire but also fits cable throttle systems. Laser cut tubing yields the smoothest corners with no slag for easy wiring. The Knurled Center for non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment.

There have been many copycat attempts to replicate our products but many customers over the years have come back because of our superior quality.  We also pride ourselves in our smooth and clean arched corners whereas competitors often use straight sharp edges which are easier to manufacture but fall short of the premium styling distinguishing riders demand.

Dominator Industries 1 1/4″ Show Chrome 16″ Meathook Monkey Bar Ape Hangers Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4 inch Meathook Monkey Bagger Ape Hanger Handlebars

When we introduced our Meathook Bagger Ape Handlebars for the 1996-2020 model years of the Harley-Davidson Electra Glide (FLH), Electra Glide Classic (FLHTC), and Street Glide (FLHX) our goal was to combine classic styling and unique attitude for Harley-Davidson owners that want the best quality with no compromises.  Ride comfort and easy installation make choosing Dominator Industries handlebars to customize your bike a no-brainer.

All of our parts are hand-made in the USA employing a multi-step manufacturing process using the finest materials. Tube diameter is 1.25” stepped down to 1” for stock/conventional controls.  Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire but also fits cable throttle systems. Laser cut tubing yields the smoothest corners with no slag for easy wiring. The Knurled Center for non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment.

There have been many copycat attempts to replicate our products but many customers over the years have come back because of our superior quality.  We also pride ourselves in our smooth and clean arched corners whereas competitors often use straight sharp edges which are easier to manufacture but fall short of the premium styling distinguishing riders demand.

Dominator Industries 1 1/4″ Chrome 13″ Meathook Monkey Bar Ape Hanger Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4 Inch Road Glide Meathook Ape Hanger Handlebars

When we introduced our Meathook Ape Hangers Handlebars for the 2015-2018 model years of the Harley-Davidson Road Glide (FLTR) our goal was to combine classic styling and unique attitude for Harley-Davidson owners that want the best quality with no compromises.  Ride comfort and easy installation make choosing Dominator Industries handlebars to customize your bike a no-brainer.

All of our parts are hand-made in the USA employing a multi-step manufacturing process using the finest materials. Tube diameter is 1.25” stepped down to 1” for stock/conventional controls.  Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire but also fits cable throttle systems. Laser cut tubing yields the smoothest corners with no slag for easy wiring. The Knurled Center for non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment.

There have been many copycat attempts to replicate our products but many customers over the years have come back because of our superior quality.  We also pride ourselves in our smooth and clean arched corners whereas competitors often use straight sharp edges which are easier to manufacture but fall short of the premium styling distinguishing riders demand.

Dominator Industries 1 1/4″ Gloss Black 16″ Meathook Monkey Bar Ape Hanger Handlebars

Total height: as advertised. Total width: 36 inches. Distance between the uprights: 15 inches. Clamping surface width: 5.25 inches. Total pullback: just over 4 inches. Amenities: 1 1/4″ bar stepped down to 1″ diameter for stock/conventional controls. Both grips have 1/2″ X 2″ slots laser cut for internal wiring purposes. The throttle side is honed out and notched for fly by wire. Laser cut tubing yields the smoothest corners we can provide so the wires roll right through and out the generous slot at the bottom. Knurled center for non slip grip.

Damn these bars are bitching! When we took to tricking out a Street Glide we wanted to combine chopper styling and attitude. We killed it! Since we introduced the Meathook Bars we’ve seen some guys trying to copy them. But the quality is simply not there. They made straight corners instead of the sexy and smooth arched points. They also have made no consideration for internal wiring where we work the inside of our bars to make your wires go through smooth like butter! There is just no cutting corners when it comes making high quality, great looking Original Meathook Bars!

Dominator Industries 1 1/4 Inch Meathook Monkey Bagger Ape Hanger Handlebars, 10 Inch Rise, Gloss Black

When we introduced our Meathook Bagger Ape Handlebars for the 1996-2018 model years of the Harley-Davidson Electra Glide (FLH), Electra Glide Classic (FLHTC), and Street Glide (FLHX) our goal was to combine classic styling and unique attitude for Harley-Davidson owners that want the best quality with no compromises.  Ride comfort and easy installation make choosing Dominator Industries handlebars to customize your bike a no-brainer.

All of our parts are hand-made in the USA employing a multi-step manufacturing process using the finest materials. Tube diameter is 1.25” stepped down to 1” for stock/conventional controls.  Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire but also fits cable throttle systems. Laser cut tubing yields the smoothest corners with no slag for easy wiring. The Knurled Center for non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment.

There have been many copycat attempts to replicate our products but many customers over the years have come back because of our superior quality.  We also pride ourselves in our smooth and clean arched corners whereas competitors often use straight sharp edges which are easier to manufacture but fall short of the premium styling distinguishing riders demand.

LA CHOPPERS LA-7321-10 Chrome 11/4″ Touring Ape Hanger Handlebars

Designed To Have Proper Clearance On Filth/Flux Models With The “Batwing” Fairing. Notched For Throttle-By-Wire. Large Laser-Cut, Burr-Free Wiring Slots.

Wild 1 Chubbys 12.5 Inch Ape Hanger Handlebars

These sensational looking custom 1 1/4″ thick bars mount on stock risers. They also work with most grips, stock controls and some custom controls. Chrome plating, Pre-drilled for internal wires. Diamond knurled mounting, and smooth bends combine for the ultimate in style and comfort. These bars also work with late model electronic throttles.

%d bloggers like this: